A heat pump extracts heat from the outside air, converting it into usable energy for heating a building or providing hot water.

An ampere is the amount of current produced by the force of one volt acting through a resistance of one ohm.

Amps or ampere is the amount of current produced by the force of one volt acting through a resistance of one ohm.

A colour of heated towel rail.

A device that heats water for use in a hydronic heating system, providing a continuous supply of hot water to the system.

Brushed nickel is nickel that has been finished by etching it with a wire brush or similar tool to give the metal a textured look.

A colour of heated towel rails.

A timer built into every Hotwire rail enabling you to turn the rail on or off.

Used to fix the heating element to the reinforcement.

A household electrical circuit simply supplies power to the areas in your home that need it. A typical circuit is 10 amps. This enables you to run appliances or devices up to 2,300 watts.

The Cold Tail is the conductive cable that runs from the Thermostat to the Heating Element.

The Cold Tail join is the connection point between the heating element and the cold tail cable.

The process of testing and verifying the proper operation of a heating system after installation, ensuring optimal performance and safety.

A contactor is another word for relay.

An alarm that is used to monitor an under floor heating element after installation and before commissioning of the heating system.

The process of heat transfer through the movement of a fluid, such as air or water, is often used in the context of heating systems.

The temperature at which air becomes saturated with moisture, causing condensation and potential issues for flooring materials.

A method of heating where electric current directly generates heat within a conductor, commonly used in electric floor heating systems.

A term commonly used to describe electric floor heating systems, which use heating cables or mats to generate heat.

A type of underfloor heating system that uses electric heating cables or mats embedded in the floor to generate heat.

A wall-mounted or ceiling-mounted flat panel that emits radiant heat, providing an alternative to traditional radiators or underfloor heating systems.

Power derived from the utilization of physical or chemical resources, especially to provide light and heat or to work machines.

The ability of a system or appliance to use energy in an effective manner, minimizing waste and reducing overall consumption.

A gap intentionally placed in a floor or wall to allow for expansion and contraction caused by changes in temperature, preventing structural damage.

Fibre Glass mesh can be used to cover the heating element to protect it during the installation of the flooring.

Tape provided to fix the element to the floor.

A type of floor construction that does not directly attach to the subfloor, often used in combination with underfloor heating systems to minimize thermal bridging.

Floor Heating is a generic term that covers a variety of products. Generally, it is achieved by an electric heating element being installed under the flooring.

A device that manages and regulates the operation of an underfloor heating system, controlling temperature and zone settings.

The maximum weight a floor can support without risk of damage or structural failure, including the weight of floor coverings, heating systems, and furniture.

A temperature-sensitive device is installed within the floor to monitor and control the heating.

A heat pump that extracts heat from the ground, using buried pipes or loops, to provide energy for heating a building or supplying hot water.

Also called gunmetal gray, a dark gray with bluish or purplish tinge.

A colour of heated towel rails.

A device or material that helps distribute heat more evenly, often used in underfloor heating systems to improve heat transfer and efficiency.

A device or surface, such as a radiator or heated floor, transfers heat from a heating system to the surrounding environment.

A device that transfers heat between two or more fluids without mixing them, often used in hydronic floor heating systems to transfer heat from the boiler to the water.

The rate of heat transfer per unit area, used to evaluate the performance of floor heating systems and insulation materials.

A process used to determine the amount of heat energy lost from a building, helping to identify the appropriate size and type of heating system needed.

A measurement of how quickly heat is lost from a building is used to determine insulation requirements and heating system sizing.

The amount of heat energy produced by a heating system, is usually measured in watts.

A device that transfers heat energy from a source, such as the ground or air, to a building, providing an energy-efficient heating solution.

A system that captures and recycles heat from exhaust air, improving indoor air quality and energy efficiency in a building.

A metal plate is used in hydronic floor heating systems to improve the distribution of heat by increasing contact between the pipes and the floor surface.

A heated towel rail is a ladder with an in built heating element that will dry towels.

A type of electric conductor designed to produce heat when an electric current passes through it, commonly used in electric floor heating systems.

A continuous loop of pipe or cable in a floor heating system, carrying heated water or electricity to provide warmth.

The Heating Element is part of the floor heating system that actually warms up.

Heating mats are generally Under Tile Heating products that are fixed to a self-adhesive fiberglass mesh.

A pre-assembled unit consisting of a heating cable attached to a flexible mesh, used for easy installation of electric floor heating systems.

Hydronic floor heating uses hot water run through pipes under the floor to heat the room. Hydronic heating can also be run through wall-mounted panel heaters.

A type of underfloor heating system that uses heated water circulated through pipes embedded in the floor to provide warmth.

In Screed Heating is a heating element that is installed in a Sand and Cement Screed. Typically this would be used in a bathroom where a “Fall” is required to a floor waste.

In Slab Heating is a heating element that is typically fixed to the reinforcement inside the concrete slab.

A heating method in which heat is transferred from the heat source to the space being heated through an intermediate medium, such as water in hydronic systems.

A diagnostic technique that uses infrared cameras to visualize temperature differences.

The distance between the top of the floor covering and the heating elements in an underfloor heating system, affecting heat transfer and performance.

Insulation can be achieved by a variety of different products installed in the roof cavity, inside walls or under the floor.

Materials used to reduce heat transfer between surfaces, improving energy efficiency and comfort in a building.

The IP Rating classifies and rates the degree of protection provided by mechanical casings and electrical enclosures against intrusion, dust, accidental contact, and water.

The total length of the continuous pipe or cable used in an underfloor heating system, influences system performance and efficiency.

A heating system that operates at lower water temperatures than traditional systems, improving energy efficiency and compatibility with renewable energy sources.

A central distribution device is used in hydronic floor heating systems to regulate the flow of heated water through the network of pipes.

Off Peak Power is an electricity tariff available during off-peak times. This is generally from late at night until early in the morning.

An ohm is a unit of electrical resistance seen between two points across a resistor, conductor, device or circuit. One ohm means that a potential difference (voltage) of 1V between these two points produces a current of 1A.

Cross-linked polyethylene (PEX) pipes, known for their flexibility and durability, commonly used in hydronic floor heating systems.

The distance between parallel pipes in a hydronic floor heating system, affects heat output and distribution.

Under Floor Heating installed under a polished concrete finish.

A heating system designed to provide the main source of heat for a building or space.

A material that reflects radiant heat, reducing heat transfer and improving insulation performance in a building.

Radiant heating is a category of HVAC technologies that exchange heat by both convection and radiation with the environments they are designed to heat.

A heating method that transfers heat through infrared radiation, warming objects and people directly rather than heating the air.

A flat surface designed to emit radiant heat, providing an alternative heating solution to traditional radiators or underfloor heating systems.

A relay may be required when installing floor heating in a larger area. It increases the Amp capacity of a thermostat.

Energy from sources that are replenished naturally and sustainably, such as solar, wind, or geothermal, often used to power heating systems.

The process of installing a new heating system, such as underfloor heating, in an existing building or structure.

The temperature of the water returning to the boiler or heat source in a hydronic heating system, after circulating through the floor.

Most Thermostats offer the functionality of sensing from both the room temperature and / or floor temperature.

The total cost of the electricity used to run the floor heating.

Sand and Cement Screed can be used to create a “fall” in a floor towards a floor waste.

A layer of material, usually cement-based, applied over a subfloor to create a smooth, level surface for the installation of floor coverings or heating systems.

A supplementary heating system used in addition to the primary heating source to provide additional warmth or localized heating.

A Self Levelling compound can be used to create a protective layer over the floor heating element.

A type of heating cable that automatically adjusts its heat output based on surrounding temperatures, improving energy efficiency and safety.

A Single Heated Rail towel rail is a towel rail where there is no vertical rail to link the horizontal rails together. You see our range here.

A technology that captures heat energy from the sun to provide hot water or space heating, often used in conjunction with floor heating systems.

A form of steel containing chromium, resistant to tarnishing and rust.

A colour of heated towel rails.

The structural layer of flooring that supports the finished floor covering and any additional layers, such as underfloor heating systems.

The temperature of the water leaving the boiler or heat source in a hydronic heating system, before entering the floor.

The difference between the supply and return temperatures in a hydronic heating system, influencing system efficiency and performance.

The layering of air within a room due to differences in temperature, which can affect the perceived comfort and efficiency of a heating system.

A Thermal barrier is a product that can be installed under a heating element to increase the efficiency.

A material or design feature that interrupts the flow of heat between two surfaces, reducing heat loss and improving insulation performance.

The transfer of heat through the structural elements of a building, which can reduce insulation performance and contribute to energy loss.

A Thermal camera can see through the flooring and the heating element will be represented by a red line. A Thermal Camera can be used to find faults or damage to floor heating.

A measure of a material’s ability to conduct heat, affecting its performance in insulation and heating systems.

A technology that captures and displays heat patterns, allowing for the identification of hot and cold spots, often used to assess underfloor heating systems.

The resistance of a material to temperature changes, affecting the responsiveness and energy efficiency of a floor heating system.

The ability of a material to store and release heat energy, contributing to the overall performance of a floor heating system.

A measure of a material’s ability to resist heat flow, influencing its effectiveness as an insulator in a building or heating system.

A Thermostat is typically a programmable device that enables the heating system to come on and off at certain times.

A device that monitors and controls the temperature of a space by adjusting the output of a heating or cooling system.

A type of thermostat that allows users to set different temperatures for different times of day, improving comfort and energy efficiency.

A Thermostat sensor runs from under the floor to the Thermostat. It senses the temperature inside or under the floor.

A style of thermostat where buttons are not required.

A Towel Rail Timer enables the scheduled control of a heated towel rail.

A type of pipe specifically designed for use in underfloor heating systems, made from materials like cross-linked polyethylene (PEX) or polybutylene (PB).

A type of plastic pipe made from polybutylene, known for its flexibility and resistance to temperature changes, often used in hydronic floor heating systems.

A style of floor heating designed for use under Carpet.

Under Floor Heating is a broad definition for any heating product that is installed under the floor of your home.

Under Tile Heating is installed on top of the subfloor immediately under the tiles.

A system that warms the floor surface by circulating heated water through pipes or using electric heating cables, providing radiant heat to the room.

A layer of material is placed beneath a floor covering to provide cushioning, insulation, and moisture protection.

A “volt” is a unit of electric potential, also known as electromotive force, and represents “the potential difference between two points of a conducting wire carrying a constant current of 1 ampere, when the power dissipated between these points is equal to 1 watt.

A type of spacer used in double-glazed windows that reduces heat loss and condensation by providing better insulation at the edge of the glass.

The period it takes for a floor heating system to reach the desired temperature after being activated.

A heat pump that extracts heat from a nearby body of water, such as a lake or river, to provide energy for heating a building or supplying hot water.

A watt is a unit of power. A watt (W) is a joule (J) of energy used or produced per second.

A term commonly used to describe hydronic floor heating systems, which use water as the heat transfer medium.

A WiFi Thermostat enables remote control of a floor heating system via an App.

The division of a heating system into separate areas, allowing for individual temperature control in different rooms or spaces.